flowmybest.blogg.se - Cisco packet tracer labs ccent

#Cisco packet tracer labs ccent serial
#Cisco packet tracer labs ccent mac

NetEss v1 Student Lab Source Files Answers.NetEss v1 Packet Tracer Activity Source Files Answers.NE 2.0 Packet Tracer Activity Lab Answers.ITN v6 Student Lab Source Files Answers.ITE v7 Student Lab Source Files Answers.ITE v6 Student Packet Tracer Source Files Answers.ITE v6 Student Lab Source Files Answers.DevNet – DEVASC – Packet Tracer Lab Answers.Cybersecurity Student Lab Source Answers.CyberOps Associate– CA – Packet Tracer Answers.CyberEss v1 Student Lab Source Files Answers.CyberEss v1 Packet Tracer Activity Source Files Answers.CCNA3 v7 – ENSA – Packet Tracer Answers.CCNA2 v7 – SRWE – Packet Tracer Answers.Which two devices allow hosts on different VLANs to communicate with each other? (Choose two.).The native VLAN is for routers and switches to exchange their management information, so it should be different from data VLANs.A separate VLAN should be used to carry uncommon untagged frames to avoid bandwidth contention on data VLANs.The security of management frames that are carried in the native VLAN can be enhanced.The native VLAN is for carrying VLAN management traffic only.What is the purpose of setting the native VLAN separate from data VLANs?.Which address type is not supported in IPv6?.They are configured as trunk interfaces.There is no media connected to the interfaces.There is a native VLAN mismatch between the switches.Why would the interfaces be missing from the output? A network administrator is reviewing port and VLAN assignments on switch S2 and notices that interfaces Gi0/1 and Gi0/2 are not included in the output. Static routes that use an exit interface will be unnecessary.Ethernet multiaccess interfaces will require fully specified static routes to avoid routing inconsistencies.

#Cisco packet tracer labs ccent serial

Serial point-to-point interfaces will require fully specified static routes to avoid routing inconsistencies.How will a router handle static routing differently if Cisco Express Forwarding is disabled?.incorrectly configured auto-MDIX feature.Which two issues might cause excessive runt and giant frames in an Ethernet network? (Choose two.).The switch interfaces FastEthernet0/2, FastEthernet0/3, and FastEthernet0/4 are configured to not negotiate and should be configured to negotiate..The switch interface FastEthernet0/1 is configured to not negotiate and should be configured to negotiate..The switch interface FastEthernet0/1 is configured as an access interface and should be configured as a trunk interface.The access interfaces do not have IP addresses and each should be configured with an IP address.Inter-VLAN communication between VLAN 10, VLAN 20, and VLAN 30 is not successful. When port security is enabled, a switch port uses the default violation mode of shutdown until specifically configured to use a different violation mode. Which feature on a Cisco router permits the forwarding of traffic for which there is no specific route?.

#Cisco packet tracer labs ccent mac

Which MAC addresses will be contained in the S1 MAC address table that is associated with the Fa0/1 port? A ping to PC3 is issued from PC0, PC1, and PC2 in this exact order. Match the packets with their destination IP address to the exiting interface on the router.

On which switch interface would an administrator configure an IP address so that the switch can be managed remotely?.

Switch(config-if)# switchport port-security mac-address 880.

Switch(config-if)# switchport port-security mac-address sticky.

Switch(config-if)# switchport port-security mac-address.

Switch(config-if)# switchport port-security maximum 40.

Switch(config-if)# switchport port-security Switch(config-if)# switchport mode access Which command does the technician need to add to the following configuration to implement this policy? Switch(config)# interface fa0/1 The security policy requires host MAC addresses to be learned dynamically, stored in the address table, and saved to the switch running configuration.

A network technician is configuring port security on a LAN switch interface.

You must have Cisco Packet tracer do not ask me for it I would Like a labs set up in packet tracer based on this web page then a recording of someone doing the labs with no voice just remarks.